If you’ve ever experienced the frustration of a garage door that won’t close, you know just how irritating it can be. Fortunately, there are a few easy ways to fix this problem.

we’ll cover the top five solutions for when your garage door wont close. With a little bit of effort and the right tools, you can get your garage door closing like new in no time!

1) Check the photo eyes

The photo eyes are a safety feature designed to detect when something is obstructing the garage door from closing. If the photo eyes are not aligned, then the garage door will not close. To check the photo eyes, look for a small light on both sides of the inside of the garage door. Make sure that the lights are shining and unobstructed by dirt or debris.

If the lights are not shining, try cleaning off the lenses with a soft cloth. You can also try adjusting the alignment of the photo eyes. This can be done by moving the sensor closer together or farther apart until the lights begin to shine brightly. If you’re having trouble with this, consider contacting a professional to adjust the photo eyes for you.

2) Check the garage door opener

The garage door opener can be the cause of many problems with your garage door not closing properly. A malfunctioning garage door opener can cause the door to reverse when it should be closing, and even prevent it from opening or closing at all. If you suspect the garage door opener is the cause of your problem, you should start by checking for any damaged or disconnected parts.

Check the power source to make sure the unit is getting adequate electricity. Check the safety sensors at the bottom of the door as well; they should be properly aligned and clean. Finally, test the remote control. Make sure the remote is in good condition, with fresh batteries and a functioning receiver. If none of these steps resolves the issue, you may need to replace the opener altogether.

3) Check the springs

If your garage door won’t close, the springs may be to blame. Garage door springs are under a lot of tension and can become damaged or worn over time. It’s important to check your springs periodically for signs of wear or damage. If your springs are damaged, they will need to be replaced.

First, you’ll need to identify which type of spring you have: torsion springs or extension springs. Torsion springs are mounted on a metal shaft above the garage door opening. Extension springs are attached to brackets near the top corners of the garage door opening.

To inspect torsion springs, start by removing any cables that are connected to them. Then, look for signs of wear and tear such as rust, cracks, broken strands, or areas of abrasion. If you find any of these, it’s time to replace the springs.

Extension springs should be checked for signs of wear or damage in much the same way. However, you’ll need to inspect both sides of the springs for any problems. Also, be sure to inspect the bracket the spring is connected to for any signs of rust or damage.

If your inspection reveals any damage, contact a professional to have the springs safely replaced. Replacing garage door springs can be dangerous, so it’s best to leave it to the experts. Once you have new springs installed, your garage door should close with ease.

Read Also: Garage Door Torsion Springs: Everything You Need to Know

4) Check the tracks

If your garage door won’t close, the first thing to do is check the tracks. The tracks are the vertical and horizontal metal bars that hold the rollers of the door. The rollers run along the track when the door is opened and closed, and the track must be aligned properly for the door to open and close properly. If the track is misaligned, the door won’t close properly.

Check the track for any damage or obstructions, such as dents, bumps, or pieces of debris. If there is any damage or obstruction, you should use a rubber mallet to pound it back into place or remove any debris. You can also use a level to make sure that the tracks are straight and aligned.

If your tracks are aligned properly but your door still won’t close, you may need to lubricate them with a lubricant like WD-40. This will help reduce friction between the track and roller, which can cause the door to jam up.

Finally, make sure that the bolts on the tracks are tightened securely. If they are loose, your door will not close properly. If you need to tighten them, use a wrench to do so.

By following these steps, you should be able to fix your garage door that won’t close. If you’re still having problems, contact a professional for assistance.

5) Check the weather stripping

Weatherstripping is an important component of your garage door. It helps to seal the bottom of the door, providing a barrier against dust, dirt, and moisture. When weather stripping becomes worn or damaged, it can cause the garage door to not close properly. To check the weather stripping, begin by examining it for signs of wear or damage.

Make sure that the weather stripping is tightly attached to the bottom of the door and not loose or sagging. If you find that the weather stripping is in need of replacement, replace it with new weather stripping.

Additionally, make sure that the weather stripping is clean and free of debris such as leaves, twigs, and dirt. If the weather stripping is dirty, clean it off with a cloth dampened with warm, soapy water. Once you’ve checked the weather stripping, test the garage door again to make sure it closes properly.